對于自動上料攪拌車干燥罐，開攪拌車的人都不陌生，它是用來過濾氣路系統內壓縮空氣中水蒸氣的，防止儲氣筒和各類泵閥遭到腐蝕，但是我發現很多用戶都不太在意這點，因此，攪拌車燥罐能否正常工作，直接影響到剎車的性能。

For the drying tank of the automatic feeding mixer truck, it is not unfamiliar to those who drive the mixer truck. It is used to filter the water vapor in the compressed air in the air circuit system, prevent corrosion of the air storage cylinder and various pump valves. However, I have found that many users are not very concerned about this. Therefore, whether the drying tank of the mixer truck can work properly directly affects the performance of the brake.

自動上料攪拌車替換干燥罐的操作并不繁瑣，利用氣罐底部的放氣閥門，來檢查氣罐底部是否濕潤，或許有水。

The operation of replacing the drying tank with an automatic feeding mixer truck is not complicated. Use the vent valve at the bottom of the gas tank to check if the bottom of the gas tank is wet or if there is water.

假如干燥罐失效，打開閥門之后會有水流出，應該當即替換新的干燥罐。好多人都是只需不出問題，幾年可能都不會換一次。并且不同品牌的干燥罐運用壽命不一樣，并且車輛行駛的氣候環境也有差異，替換的周期就很難一致。

If the drying tank fails and water flows out after opening the valve, a new drying tank should be replaced immediately. Many people just don't need to have problems and may not change once in a few years. Moreover, the service life of different brands of drying tanks varies, and the climate environment in which vehicles are driven also varies, making it difficult to maintain a consistent replacement cycle.

假如攪拌車司機們確實不知道何時該替換，能夠通過檢查儲氣筒是否有積水的方法來判斷。

If the mixer truck drivers really don't know when to replace it, they can determine by checking if there is water accumulation in the air storage tank.

可是在這里也要提示司機朋友們，由于攪拌車干燥罐連接著氣路，罐體內部與外界有必定的壓力差，壓縮空氣未排空時冒然拆開，壓縮空氣瞬間釋放，易對拆開人員形成損傷。

But here, it is also important to remind drivers that due to the connection of the drying tank of the mixing truck to the air circuit, there is a certain pressure difference between the inside of the tank and the outside. If the compressed air is not emptied, it can be opened recklessly, and the compressed air is instantly released, which can easily cause damage to the dismantling personnel.

1、我們可以從氣罐下手，利用氣罐底部的放氣閥門，來查看氣罐底部是否潮濕，或者有水。因為閥門正好位于氣罐底部。同時水的比重較大，如果干燥器失效，那么氣路中的濕氣因為重力自然會攢到氣罐底部，也就是閥門上方。

1. We can start from the gas tank and use the vent valve at the bottom of the gas tank to check if the bottom of the gas tank is damp or there is water. Because the valve is located exactly at the bottom of the gas tank. At the same time, the specific gravity of water is relatively high. If the dryer fails, the moisture in the gas path will naturally accumulate at the bottom of the gas tank, which is above the valve, due to gravity.

2、還有一種方法就是，通過釋放各個制動分泵的卸壓閥來檢查車輛氣路中是否含水。尤其是在冬天，氣溫低，一定要注意檢查管路中是否有水，防止制動失效，干燥罐滲漏，劣質的干燥罐是比較容易滲漏的，而且如果是在氣候潮濕的南方，干燥罐的使用壽命也會縮短。相反北方由于氣候比較干燥，北方的攪拌車的干燥罐使用壽命就比較長。

2. Another method is to check for water in the vehicle's air circuit by releasing the pressure relief valves of each brake cylinder. Especially in winter, when the temperature is low, it is important to check for water in the pipeline to prevent brake failure and leakage from the drying tank. Poor quality drying tanks are more prone to leakage, and if located in the humid southern climate, the service life of the drying tank will also be shortened. On the contrary, due to the relatively dry climate in the north, the drying tanks of mixing trucks in the north have a longer service life.

判斷自動上料攪拌車干燥罐是否需要更換的相關內容就講解到這里了，您對此有怎樣的疑惑或者需求，就來我們網站http://www.www.boy7up.cn咨詢！

That's all for determining whether the drying tank of the automatic feeding mixer needs to be replaced. If you have any doubts or needs about this, please come to our website http://www.www.boy7up.cn consulting service