自動上料攪拌車的檢修在整個工程作業中也是為重要的，做好基本的檢修我們的工作才能正常進行。下面小編為您進行講解。

The maintenance of the automatic feeding mixer is also important in the whole project operation, and our work can be carried out normally only after the basic maintenance is completed. The following section will explain for you.

先將砂紙置于ATF油中，浸泡約30分鐘。小心地敲擊閥體，使卡滯的閥桿從閥腔孔中落下?？赡苡斜匾褂靡话研÷萁z刀，將其撬出。

First place the sandpaper in ATF oil and soak it for about 30 minutes. Knock the valve body carefully to make the stuck valve stem fall from the valve chamber hole. It may be necessary to use a small screwdriver to lever it out.

然后自動上料攪拌車小心不要劃傷閥孔。單向閥桿是否有摩擦痕跡。使用ATF油浸泡過的#600砂紙，打磨閥桿上的毛刺，然后在溶劑中清洗閥桿并用壓縮空氣吹干。卷起半張ATF油浸泡過的#600砂紙，將其插入卡滯閥桿的閥孔中。

Then the automatic feeding mixer truck shall be careful not to scratch the valve hole. Check whether the one-way valve rod has friction traces. Use # 600 sandpaper soaked in ATF oil to polish the burrs on the valve stem, then clean the valve stem in solvent and blow it dry with compressed air. Roll up half of # 600 sandpaper soaked in ATF oil, and insert it into the valve hole where the valve stem is stuck.

輕輕扭動砂紙，使砂紙松卷，緊密貼合在閥孔表面，然后邊推拉，邊扭卷砂紙，打磨閥孔。抽出#600砂紙。在溶劑中清洗整個閥體，然后用壓縮空氣吹干。

Gently twist the sandpaper to make it loose and tightly fit on the surface of the valve hole, and then push and pull while twisting the sandpaper to polish the valve hole. Pull out # 600 sandpaper. Clean the whole valve body in solvent and blow it dry with compressed air.

在閥桿表面涂ATF油，然后將其落入閥孔中。閥桿應能靠自重落入閥孔底部。否則，重復步驟，重新測試。如果閥桿仍然卡滯，則更換閥體。

Coat the surface of the valve stem with ATF oil, and then drop it into the valve hole. The valve stem shall be able to fall into the bottom of the valve hole by its own weight. Otherwise, repeat Step and retest. If the valve stem is still stuck, replace the valve body.

自動上料攪拌車用溶劑清理閥桿和閥體。用壓縮空氣吹干所有零件，然后用ATF油作為潤滑劑，重新組裝。

Clean the valve rod and valve body with solvent for the automatic feeding mixer. Dry all parts with compressed air, then reassemble with ATF oil as lubricant.

了解了以上的檢修知識，大家可以放心對我們的設備進行檢修，大家在選擇自動上料攪拌車的時候我們會有專門的人士為大家解答，建議大收工時，要清洗混凝土貯罐及進出料口周圍，保證不粘有水泥及混凝土結塊。更多相關內容就來我們網站http://www.www.boy7up.cn進行咨詢！

After knowing the above maintenance knowledge, you can rest assured that our equipment will be overhauled. When you choose the automatic feeding mixer, we will have a special person to answer for you. It is recommended that the concrete storage tank and around the inlet and outlet should be cleaned at the end of the project to ensure that there is no cement and concrete caking. More relevant content will come to our website http://www.www.boy7up.cn Consult!