每位車主在每天出車前對自動上料攪拌車進行一些必備檢查是必須的，這樣能對車輛出現的問題早發現、早處理，不僅能節省維修費用，也會降低營運成本。現為車主朋友介紹如下：
It is necessary for each car owner to conduct some necessary inspections of the automatic feeding mixer truck before leaving every day. This can detect and handle problems that occur in the vehicle early, not only saving maintenance costs but also reducing operating costs. I would like to introduce myself to the car owner as follows:
1. Carefully check whether all components of the automatic feeding mixer truck are normal
做好安全措施，防止裝料的攪拌車壞在路上?；炷列枰煌５臄噭右苑乐鼓?，如果出現故障導致攪拌罐停轉，很容易出現悶罐。一般停罐不能超過2個小時，C40往上級別的混凝土基本就不能停。啟動自動上料攪拌車前，必須先檢查機油、潤滑油和冷卻水等物料是否充足，及時進行添加。
Take safety measures to prevent the loading mixer truck from damaging on the road. Concrete needs to be stirred continuously to prevent solidification. If a malfunction causes the mixing tank to stop rotating, it is easy to cause tank blockage. Generally, the tank cannot be stopped for more than 2 hours, and concrete with a C40 level or higher cannot be stopped. Before starting the automatic feeding mixer truck, it is necessary to check whether the materials such as engine oil, lubricating oil, and cooling water are sufficient and add them in a timely manner.
車子啟動后，低速旋轉罐體，繞車一周檢測胎壓，防止有漏氣車胎，用工具拿掉卡在輪胎中石子等雜物。由于攪拌車工作環境惡劣，車輪每天都在快速磨損，因此每天對車輛輪胎的檢查是非常必要的。
After the car starts, rotate the tank at low speed and test the tire pressure around the car to prevent any air leaks. Use tools to remove debris such as stones stuck in the tires. Due to the harsh working environment of the mixer truck, the wheels wear rapidly every day, so it is necessary to inspect the vehicle's tires every day.
其次檢驗燈光是否正常，務必保證照著輪胎邊緣，防止被工地堆放的鋼筋雜物割傷。清理干凈后視鏡和窗戶玻璃，司機保持清晰開闊視野，以應對工地的復雜工況場景。
Secondly, check whether the lighting is normal, and make sure to illuminate the edge of the tire to prevent it from being cut by the steel bars and debris piled up on the construction site. Clean the rearview mirror and window glass, and the driver maintains a clear and open view to cope with the complex working conditions of the construction site.
2、準備足夠的水和減水劑
2. Prepare sufficient water and water reducing agent
水可以應對混凝土物料干燥無法卸料的情況，減水劑也是同理，防止悶罐。
Water can cope with situations where concrete materials are dry and cannot be unloaded, and the same applies to water reducing agents to prevent tank tightness.
3、啟動攪拌車時確保攪拌罐處于靜止狀態
3. Ensure that the mixing tank is stationary when starting the mixer truck
發動機啟動時罐子如果處于高速旋轉狀態，瞬間的力會非常大，容易使減速機磨損，降低使用壽命。
When the engine starts, if the jar is in a high-speed rotating state, the instantaneous force will be very large, which is easy to cause wear on the gearbox and reduce its service life.
4、車碟的檢查
4. Inspection of vehicle discs
自動上料攪拌車用了一段時間后，剎車碟上會出現明顯的凹槽。說起來這個原因可能是自動上料攪拌車行駛在砂石路面上時，一些細小的砂石卡在剎車碟與擋泥板之間，不斷磨擦剎車碟的表面，所以出現凹槽。
After using the automatic feeding mixer truck for a period of time, obvious grooves will appear on the brake disc. The reason for this may be that when the automatic loading mixer truck is driving on a gravel road, some small sand and stones get stuck between the brake disc and the mudguard, constantly rubbing against the surface of the brake disc, resulting in grooves.
而發生這種情況時，自動上料攪拌車在行走時可能會發出“當啷、當啷”的聲音，在有些情況下剎時還會聽到尖叫聲。而針對這種情況，我們可以透過自動上料攪拌車輪胎鋁合金鋼圈目測剎車碟表面，剎車碟表面如果光滑，那就表明是正常的。
When this situation occurs, the automatic feeding mixer truck may make a "clanking, clanking" sound while walking, and in some cases, a scream may be heard when braking. In response to this situation, we can visually inspect the surface of the brake disc through the aluminum alloy steel rims of the automatic loading mixer truck tires. If the surface of the brake disc is smooth, it indicates that it is normal.
I hope that the majority of car owners can follow the above points before driving every day. I believe it will be of great help to the safe driving of your beloved car. For more related content, come to our website http://www.www.boy7up.cn Consult!
點擊撥打服務熱線：400-879-1999